background background

Little Tree is a fertile ground for green builders and home owners in Bali who are in need of eco-friendly building materials and home supplies. Green buildings... that's us!

Little Tree Bali - Green Building Centre

by email

by phone

Customer Service
+62 (0) 81139605497

If you have a special request please feel free to contact our staff directly.

in our store

Now open from Monday to Saturday:
8:00 - 17:00

Little Tree Spirit Pre-Sealant

For Clay and Stone

Spirit Sealant is a water based penetrating sealant that will thoroughly seal porous clay cement, sand stone, limestone and other natural



product-image-1
ENQUIRE ABOUT THIS PRODUCT

Spirit Pre-Seal is a water based seal that works by penetrating into the stone. After drying the seal will stop capillary action in the stone. This will prevent any water or water based staining materials from absorbing into the stone. This is very important in stopping water marking from occurring during the laying process and assist future stain prevention by providing a foundational product that performs for many years.

Spirit Pre-Seal will not affect adhesion or interfere with the laying of the stone, but will act as a grout release to assist in the removal of grout haze, this is important as the use of acid products can damage some stones. If the stone is not going to be exposed to oil or food that may contain oil, then pre-seal will act as a final seal with years of performance. If the area is going to be used for entertainment or food areas, the stone should be further sealed with Spirit Water-based Premium Seal.

USES

  • Gives a high level off protection against grout and sub-surface staining off water-borne contaminants on the following products:
  • Terracotta and unglazed porous clay
  • Natural stones such as limestone, slate, sandstone, honed sandblasted & flamed granite and flagstone
  • Concrete and clay & cement pavers
  • Unpolished marble & porous granite

CHARACTERISTICS

  • Contains a glass type resin compound
  • Internal and external use
  • Has no fumes or odor
  • Fast sealing and curing - allows foot traffic in 30 minutes
  • High resistance to grout and water-borne contaminants
  • Permits vapor transmission
  • Non-D.G
  • Mould & mildew resistant
  • Stone can be dipped in sealer before laying
  • Excellent pre-grout release
  • Facilitates on-going maintenance off porous tiles
  • Non-flammable
  • Non-toxic
  • Water-based penetrating seal leaving a natural look
  • Suitable for internal & external use
  • Last up to 5 years
  • For use on all Natural Stone & tiles
  • Provide a natural look finish
  • Does not affect adhesion of glues & grout
  • Low VOC

 

Available size: 1 l


COVERAGE

Coverage will depend on porosity of tiles, temperature and method of application. Use full strength, do not dilute.

Approximate coverage’s area:

  • Terracotta 1 litre per 8-10 m²
  • Slate 1 litre per 10-12 m²
  • Limestone 1 litre per 6-8 m²
  • Travertine 1 litre per 10-12 m²

 

APPLICATION

Dipping


This is the most preferred way of applying Pre-Seal as it will seal all six sides and assure that the seal is applied evenly through the stone.

Lambswool

A lambswool applicator can be used; in order to seal the stone properly you must make sure that the sides of the stone are sealed as well.

Spraying

This technique is quiet fast however it is important that you don’t let the sealer pool on the stone as this can cause an excess problem.

Once the stone has been sealed with Pre-Seal by any of the above methods it is important that the sealer can dry and cure properly. The stone now needs to air dry, if they are stacked wet or packed pack in a crate they will not dry and the sealer may not perform. Spirit Pre-Seal needs 24 hours to cure fully before they can be laid. It is recommended that the stone is wiped with a white cotton cloth before stacking; this will prevent the tile sitting in a puddle of Pre-Seal. The above picture is showing how you can to stack the tiles correctly.

 

METHOD OF APPLICATION

  1. Always do a small trial area first in an inconspicuous area to ensure application competence and satisfaction with results.
  2. Ensure surface to be sealed is sound and dry, thoroughly clean and free from oils, grease, paint, and grout or cement residue, efflorescence or acid.
  3. Apply Spirit Pre-Seal undiluted using a dense sponge squeegee mop, Lambswool applicator or pump garden sprayer.
  4. Work to full tiles to avoid over-lapping and remove any sealer which has not been absorbed after 2 minutes with a dry absorbent cloth.
  5. On very porous surfaces only – such as Mexican terracotta, a second coat may be required. Accordingly, repeat stages 2 & 3 above. However, wait a minimum of 4 hours before applying the second coat.
  6. In the event of excess sealer being left on the tiles a white haze/bloom may form. This can be removed using a nylon scouring pad and a very dilute solution of Spirit Phosphoric Acid Cleaner or Spirit H.D.C. The tiles must then be washed with plain water to ensure no residue remains.
  7. Spirit Pre-Seal cures fully within 24 hours. However, the sealed tiles can be walked on after about 30 minutes.

 

MAINTENANCE

Regular daily cleaning: Use Spirit Neutral Cleaner

Periodical cleaning: Use Spirit HDC

Physical Description: Clear, colourless liquid

Odour: No odour

Boiling Point: Approximately 100°C at 100kPa

Freezing/Melting Point: Approximately 0°C

Volatiles: Water component

Vapour Pressure: 2.37 kPa at 20°C (water vapour pressure)

Specific Gravity: Approx 1.02

Water Solubility: Completely soluble in water

Risk phrases: Potassium Hydroxide >=0.5%Conc<2%: Xi; R36/38

R38, R41. Irritating skin, serious damage to eyes


SIMILAR PRODUCTS


Don't know where to start?
Check our guide
Need product information?
Talk with our sales team
Why build green?

signup for product updates


privacy policy
Sari Organic - Vegetarian Cafe